Objectarx insert block插入块

admin1

如果我从Autocad执行简单插入块，它总是以在UCS中绘制块的方式插入块。一、 e.如果块有一个控制柄，并且在绘制时该控制柄指向XY平面中的Y+，则默认情况下，Autocad将始终将块插入UCS的XY平面，并将控制柄指向Y+。





但在使用[code][code][code]Objectarx insert block插入块[/code][/code][/code]时，情况似乎并非如此。我可以设置UCS使Y+指向水平方向，但插入块时控制柄仍然指向垂直方向[code]if (m_BlockRef)
        {
                delete m_BlockRef;
                m_BlockRef = nullptr;
        }

        m_DirPt = dir_pt;
        m_BlockRef = new AcDbBlockReference();
        m_BlockRef->setBlockTableRecord(blk_objid);

        // Calcualte Normal : refactor as function
        AcGeVector3d vec = endPoint().asVector() - startPoint().asVector();
        AcGeVector3d vec1 =m_DirPt.asVector() - startPoint().asVector();
        AcGeVector3d vec_normal = vec.crossProduct(vec1);
        vec_normal.normalize();

        // Get UCS, refactor as a function
        AcGeMatrix3d  myUCS;
        acdbUcsMatrix(myUCS, nullptr);
        AcGeVector3d  xAxis, yAxis, zAxis;
        AcGePoint3d   myOrigin;
        myUCS.getCoordSystem(myOrigin, xAxis, yAxis, zAxis);

        bool AngleFlip = false;
        if (fabs (vec_normal.dotProduct(zAxis) ) < 1e-8)
                return;
        else if (vec_normal.dotProduct(zAxis)  < 0)
                AngleFlip = true;
        else
                AngleFlip = false;

        m_BlockRef->setNormal(zAxis) ; //(vec_normal);
        m_BlockRef->setPosition(ins_pt);
        AcGeScale3d scl;
        if (scale < 0)
                scale = 1.0;
        scl.set(scale, scale, scale);
        m_BlockRef->setScaleFactors(scl);

        // calculate angle
        ads_point p_start_wcs, p_end_wcs, p_start_ucs, p_end_ucs;
        p_start_wcs[X] = startPoint().x ; p_start_wcs[Y] = startPoint().y ; p_start_wcs[Z] = startPoint().z;
        p_end_wcs[X] = endPoint().x ; p_end_wcs[Y] = endPoint().y ; p_end_wcs[Z] = endPoint().z;
        ConvertFromWCSToUCS(p_start_wcs, p_start_ucs);
        ConvertFromWCSToUCS(p_end_wcs, p_end_ucs);
        AcGePoint3d p_start(p_start_ucs[X], p_start_ucs[Y], p_start_ucs[Z]);
        AcGePoint3d p_end(p_end_ucs[X], p_end_ucs[Y], p_end_ucs[Z]);
        AcGeVector3d v1_ucs = p_end.asVector() - p_start.asVector();
        AcGeVector3d v1 = endPoint().asVector() - startPoint().asVector();

        AcGeVector3d ref_vector = AcGeVector3d::kZAxis;
        double dangle  = xAxis.angleTo(v1_ucs, zAxis); // this is not what I want?
        double dangle1 = AcGeVector3d::kXAxis.angleTo(v1_ucs,AcGeVector3d::kZAxis);

        if (m_AngleFlip )
        {
                dangle1 *= -1;
                m_FlipHandle = !m_FlipHandle;
        }
        m_BlockRef->setRotation(dangle1 );[/code]。